Exterior roller blind for windows

CLIP'N'SHADE external roller blind for windows

PRODUCT DESCRIPTION

CLIP'N'SHADE outdoor roller blind is a clampable roller blind that effectively protects the home from heat. It is simply clamped into the window with the help of five clips - the installation takes only a few minutes and can be done by anyone independently. No scaffolding is needed for the installation, as it can be done from the inside. Of course, there is no need to drill or screw into the window or facade. Because it is attached to the outside of the window, the special heat protection fabric reflects the heat rays of the sun. The heat input is thus reduced by over 90% and it remains cool in the apartment!

You can find more information on colors, fabrics and other features of our external roller blinds here.

Would you like a special color that perfectly matches your home? No problem! We can coat your external roller blind against heat in all RAL colors for 129€!

HOW DO I CHOOSE THE RIGHT WIDTH?

Determining the appropriate width is actually quite simple. The prerequisite is that your reveal width (see image 1) is less than 150 cm. If the reveal width is greater than 150 cm, you can simply install two of our external roller blinds next to each other (see image 2). The reveal width is the width of the masonry opening for the window, i.e. from the masonry on the left to the masonry on the right.
IMPORTANT: This is an OUTDOOR roller blind, which is why the measurements are taken from the outside of the window. Always measure the reveal width in several places (top, middle, bottom). Then take the smallest measurement as the reveal width.

Figure 1: This is how you determine your reveal width.

As soon as you have determined the reveal width, round down to the next possible order width.
For example, if you have a reveal width of 105 cm, order the 100 cm wide external roller blind.

If the reveal width is greater than 150 cm, you can use two external roller blinds for your window, as shown in the picture below. This is particularly the case with double-sash windows. In this case, try to select the order width of our roller blind so that the guide rails are behind the window frame profile or the window sash profile.

Figure 2: Installation of two CLIP'N'SHADE external roller blinds side by side

IF YOU HAVE ANY QUESTIONS, YOU CAN ALWAYS CONTACT OUR CUSTOMER SERVICE. Send us an email to info@clipnshade.de or contact us via our form. You can find it here.

HOW DO I CHOOSE THE RIGHT HEIGHT?

1. In height, all our roller blinds are very flexible, so you only need to choose the right range (eg: 91-140cm). By means of the telescopic guide rails you then set the exact height during installation.
2. Measure the clear window height of your (open!) window as shown in the picture. IMPORTANT: The window frame must be visible at least 1.5cm above the outside!
3. Select the appropriate area from the drop-down menu.

Our standard widths do not fit?
Then take a look at our CLIP'N'SHADE Customized products. Here you can find our exterior roller blinds for windows and balcony doors, also tailored to your window to the millimeter.

• 

  CLIP'N'SHADE - external roller blind made to measure for balcony doors

  Ab 394,00 €

• 

  CLIP'N'SHADE - external roller blind made to measure for windows

  Ab 285,00 €

DOES THE CLIP'N'SHADE EXTERIOR BLIND ALSO FIT MY WINDOW?

Our outdoor roller blind fits 90% of all windows - but there are a few exceptions that you should check before placing your order:

1. Your window must be able to open. If it is a fixed glazing, our external roller blind can not be installed.
2. Windows with skylights or sidelights. Skylights are additional window units above or below your main window. Often the installation of our external blinds is still possible. Please contact us before you place your order.
3. Cane overturnThe overlap is the outermost elevation of your window frame profile. For plastic windows usually about 1.5-2.5 cm. Important: If a rubber seal is present, please measure it as well. Is your overlap greater than 2.5 cm please contact us via the Contact form. You can find a picture of how to measure the stick overlap here:
4. Wooden window with rain railA rain channel is a thin metal profile on your window frame. It replaces the stick overlap and is intended to prevent water from entering the window. Often a CLIP'N'SHADE can be mounted anyway - please contact us in any case via the Contact form. You can find a picture of a rain track here:
   
5. Wooden window with weatherboard: A weatherstrip is a protruding profile on the window sash that is designed to prevent water from entering the window. Actually a great thing, but hinders the installation of our blind. If the weather bar extends beyond the profile of the window frame, our CLIP'N'SHADE exterior roller blind unfortunately cannot be installed. You can find a picture of a weather bar here:
   

Assembly video

The following link will take you to our installation video on YouTube: https://www.youtube.com/watch?v=2ksf3sImhuk

EXCHANGE AND REVOCATION

As this product is a standard size, you have two weeks from receipt of the product to test it. Within this time, you can return it to us at any time free of charge and we will refund you the full price. Please send us a short e-mail to info@clipnshade.de stating the reason for the return and your order number. Thank you very much!